This is an old revision of the document!


A PCRE internal error occured. This might be caused by a faulty plugin

===== Week 5 [ Mon 21 Jun 2010 - Sun 27 Jun 2010 ] ===== ==== Day 1 [ Mon 21 Jun 2010 ] ==== Git commit: [[http://git.etherboot.org/?p=people/andreif/gpxe.git;a=commit;h=0906919af2982e3f285287035c210e101fafd783|0906919af2982e3f285287035c210e101fafd783]] Today I continued with my work on the forcedeth driver. Eventually I reached a point where I really needed the registers mapped. At this point, I was really confused since I saw that most of the drivers simply got ioaddr as the base address or used ioremap to get a memory mapped BAR. The Linux driver can't do this since some models have different register sizes (i guess this is the total size of all registers). So, it has to search all the BARs and select the one which describes the largest memory area. I had to go a bit more low-level to do this, and use some pci_* routines. With stefanha's help I did manage to do it eventually. I spent most of the time reading up on the PCI specification and studying to see if other drivers have this problem. There is the ''via-velocity'' driver which has a similar problem and implements its own ''pci_resource_flags routine''. Perhaps this should be moved to a common header somewhere. Tomorrow I'll finish .probe and do the first tests on the NIC I have :) ==== Day 2 [ Tue 22 Jun 2010 ] ==== Git commit: [[http://git.etherboot.org/?p=people/andreif/gpxe.git;a=commit;h=57da3ac719c5a15cf772dfa2cc5bf93cf6434eb5|57da3ac719c5a15cf772dfa2cc5bf93cf6434eb5]] Well, I guess one should not count his chickens before they hatch. The .probe routine branched into a lot of other routines, some of which were not that easy to understand. There is yet another routine I have to implement ''phy_init'' which I'll get to tomorrow. In other news, I posted my r8169 patch today. ==== Day 3 [ Wed 23 Jun 2010 ] ==== Git commit: [[http://git.etherboot.org/?p=people/andreif/gpxe.git;a=commit;h=a344aefa7cc02caa32aa4bb85f23748f7673d676|a344aefa7cc02caa32aa4bb85f23748f7673d676]] Finally the implementations are done. I managed to finish both .probe and .remove today, along with some auxiliary routines they used. There is a surprising amount of code involved, mostly due to small vendor-specific tweaks. I'll post a description tomorrow regarding the registers I've used so far, and what I have learned about the NICs. The code will have to be cleaned, I have some routines a gazillion lines long. Everything's ready for the first test tomorrow. ==== Day 4 [ Thu 24 Jun 2010 ] ==== Git commit: [[http://git.etherboot.org/?p=people/andreif/gpxe.git;a=commit;h=5756a78e83b6a83851a07fce80b2993772b772ce|5756a78e83b6a83851a07fce80b2993772b772ce]] Lots'o'issues today. * Using the ''forcedeth.usb'' image does not work. At first I thought that there was a problem with my USB stick, but then Marty confirmed that this seems to be an issue with a lot of systems and suggested I use SYSLINUX instead. And so I did. I followed the instructions from [[http://www.etherboot.org/wiki/eb_imagetypes?s[]=usb&s[]=boot#usb_flash_etherboot_-_general_hard_disk_boot_geometry|here]] to create the bootable stick. It worked, but SYSLINUX gave an error: **cannot find kernel image**. It was surprising since ''forcedeth.lkrn'' was there on the stick and the ''syslinux.cfg'' file was correct. Well, I learned something new because of this; since I formatted the disk with ''mkdosfs'', the filnames have [[http://en.wikipedia.org/wiki/8.3_filename|a restriction]]. Renaming ''forcedeth.lkrn'' to ''forcedet.lkr'' and modifying the ''syslinux.cfg'' accordingly, I managed to get gPXE to boot. * And yet, it doesn't work! Naturally I now enabled debugging messages to see how the .probe routine behaved. Nothing showed up. I enabled debugging in PCI too and that didn't work either. In case someone else runs into the same problems, here are some of the things you might want to look for (all compiled from the discussion I had today with Marty and Stefan): * the file you want to debug does have actual DBG messages * output is redirected to the serial console (''config/console.h'') * check the link map to see if the object you're debugging gets imported * make sure the driver does have a PCI_ROM statement that corresponds to the NIC's characteristics * call ''adjust_pci_device()'' * make sure the struct pci_driver isn't tagged with an __unused label The last two of these were the problems I've had, but I went through all of them in order to figure out what the problem was. As a result, .probe now works, life is good. Of course, bugs related to it will surface once I implement the other routines. I didn't get to do anything else today, I'll have to catch up tomorrow. As Stefan said, booting from an USB stick can be a real pain because of the constant dd-ing and moving of the switch from one USB port to another. As he suggested, I'll get a switch and setup a small DHCP server that can service the forcedeth machine with an image it can chainload. Hurray for using gPXE for the first time on a physical machine ^_^


Navigation

* [[:start|Home]] * [[:about|About our Project]] * [[:download|Download]] * [[:screenshots|Screenshots]] * Documentation * [[:howtos|HowTo Guides]] * [[:appnotes|Application Notes]] * [[:faq:|FAQs]] * [[:doc|General Doc]] * [[:talks|Videos, Talks, and Papers]] * [[:hardwareissues|Hardware Issues]] * [[:mailinglists|Mailing lists]] * [[http://support.etherboot.org/|Bugtracker]] * [[:contributing|Contributing]] * [[:editing_permission|Wiki Edit Permission]] * [[:wiki:syntax|Wiki Syntax]] * [[:contact|Contact]] * [[:relatedlinks|Related Links]] * [[:commerciallinks|Commercial Links]] * [[:acknowledgements|Acknowledgements]] * [[:logos|Logo Art]]

QR Code
QR Code soc:2010:andreif:journal:week5 (generated for current page)