This is an old revision of the document!


Etherboot command-line

Network Interfaces

Etherboot names interfaces following the pattern “net#”.

ifstat [interfaces…] Displays information and statistics about the specified interface. If no interface is specified, displays information about all detected interfaces. Information includes MAC address, PCI bus/slot/function identiers, and packet counts.

ifopen [interfaces…] Opens the specified interfaces. If no interface is specified, opens all interfaces.

ifclose [interfaces…] Closes the specified interfaces. If no interface is specified, closes all interfaces.

dhcp <interface> Attempts to configure the specified network interface using DHCP. Also opens the interface.

Working with images

imgfetch [-n|–name <image name>] <filename> [arguments…] Retrieves an image file, giving it a specified name, and prepares it to be executed with the specified arguments. File name may be a simple path, or an HTTP URL. Simple paths are assumed to be located on the TFTP server specified by dhcp or config. If image name is not specified, the base filename will be used as the name.

module [-n|–name <image name>] <filename> [arguments…] Equivalent to imgfetch

initrd [-n|–name <image name>] <filename> [arguments] Equivalent to imgfetch

imgargs <image name> Set or change the arguments for the specified image name.

imgload <image name> Prepares an executable image to be booted.

imgexec [image name] Execute the loaded image, or a specified image. If more than one image is loaded, the image must be specified. Note, if the specified image is not the most recently loaded one, Bad Things will almost certainly happen. This should only be done in special cases.

boot [image name] Equivalent to imgexec

imgfree Remove all fetched/loaded images.

kernel [-n|–name <image name>] <filename> [arguments] Fetch and load a bzImage format Linux kernel. Equivalent to an imgfetch followed by imgload.

Runtime configuration

config [scope] Enter a GUI to set up runtime configuration. On some systems (cards) this may be stored in NVRAM. Scope allows the GUI to override or view specific subsets of options. (see below)

set <identifier> <value> Set the value of identifier to value.

show <identifier> Display the value of identifier

clear <identifier> Clear the value of identifier

Identifiers

All identifiers are set within a scope.

  • root (scope unspecified)
  • proxydhcp Settings from a Proxy DHCP server (Needs more description)
  • [interface] e.g. net0. Settings for a network device.
  • [interface].dhcp. Settings from the DHCP server acquired by interface. Read/write, but note that you cannot specify new options that were not already provided.
  • [interface].nvo. Read/write settings in NVRAM on certain supported cards. WARNING this permanently modifies settings on your network card. It is possible to damage your network card by changing settings in this context. Use at your own risk.
  • smbios. Read-only access to settings in the System Management BIOS (see below)

Identifiers follow the format [scope/]identifier:[type]. For example, to set the IP address of the 'net0' card use set net0/ip XXX.XXX.XXX.XXX

Options not specified in a higher scope will be read from a lower one. So if the option ip is unspecified, it will be read from net0/ip; if the option net0/ip is unspecified, it will be read from net0.dhcp.

Root

hostname The system's hostname. Sent to the DHCP server for dynamic DNS changes, or specified by the DHCP server. Equivalent to DHCP option 12 (host name)

filename The boot image to be loaded. Equivalent to DHCP option 67 (Bootfile name)

root-path NFS/iSCSI root path. The path to a network root filesystem. Equivalent to DHCP option 17 (Root Path)

username Username to be used for any authentication. Currently only used by iSCSI.

password Password to be used for any authentication. Currently only used by iSCSI. Intended to be stored in card NVRAM, but see warning above.

priority

Network device

ip The device's IPv4 address

netmask The device's IPv4 subnet mask

gateway The device's default gateway

mac The device's MAC address

dhcp-server The dhcp server from which settings were obtained

dns-server The DNS server to use for resolving hostnames

next-server The (TFTP) server from which to obtain files when not specifying an HTTP URL

initiator_iqn_setting The iSCSI initiator name

SMBIOS

Read-only access to the system's Systems Management BIOS. Identifiers follow the format <type>.<offset>.<length>:<format>. Example: To read the Manufacturer name, get smbios/1.4.0:string will read SMBIOS offset 4 as a string. Valid formats: string, ipv4, int8, int16, int32, uint8, uint16, uint32, hex, uuid

uuid The system's UUID

Other

autoboot Attempts to boot the system, as follows:

  • Wait for a link on ethernet
  • Configure via DHCP
  • Boot an embedded image (?)
  • download (and exec) the DHCP-specified boot filename
  • boot from the DHCP-specified root path, using iSCSI or ATA-over-Ethernet (AoE)

exit Exits gPXE, and passes boot control back to the BIOS, which generally attempts to boot the system using the next available boot method.

sanboot Attempts to boot the system from a SAN device (iSCSI or AoE) using the DHCP-specified root path.

Outstanding questions

  • What does autoboot do? Does it simply execute a script, pre-defined at compile time? Does it follow its own sequence of boot operations?
  • When multiple images of the same name are fetched, which one will takes precedence?

QR Code
QR Code commandline (generated for current page)