Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
wiki:qemupxeknifehttp [2009/05/23 10:36]
less1
wiki:qemupxeknifehttp [2009/05/23 13:59]
less1
Line 1: Line 1:
-====== Get PXE Knife working with QEMU over HTTP ======+====== Get PxeLinux and PXE-Knife working with QEMU over HTTP ======
  
-I am taking similar approach as I took for TFTP for which QEMU + PXE Knife combination is working if I use qemu TFTP stack. +Note : use latest version of Pxelinux to work over HTTP, for me version 3.80 worked.
-Here are the things that are working ​for me. +
-<​code>​ +
-qemu -net nic -net user -fda ./gpxe.dsk -bootp /pxelinux.0 -tftp /​home/​myname/​for_pxe_knife/​ +
-</​code>​ +
-which boots pxe-knife over tftp and  +
-<​code>​ +
-qemu -fda gpxe.dsk -net nic -net user -bootp http://​10.0.0.2/​gpxe/​gtest.gpxe +
-</​code>​ +
-boots gtest.gpxe which is copy of [[http://​etherboot.org/​gtest/​gtest.gpxe]].\\+
  
-But when I try and use HTTP with qemu over pxe_knife which is based on __pxelinux__,​ +Following ​is the way to run Pxe-knife (or any pxelinux ​based system) over http.
-it does not work.+
 <​code> ​ <​code> ​
 qemu -fda gpxe.dsk -net nic -net user -bootp http://​10.0.0.2/​pxeknife/​pxelinux.0 qemu -fda gpxe.dsk -net nic -net user -bootp http://​10.0.0.2/​pxeknife/​pxelinux.0
 </​code>​ </​code>​
-It loads pxelinux.0 successfully,​ but fails in loading //​pxeknife/​default//​ file with error  
-<​code>​ 
-TFTP prefix: http://​10.0.2.2/​ 
-Trying to load: pxelinux.cfg/​default 
-Unable to locate configuration file 
  
-Boot failed: press a key to retry, ​or wait for reset...+or you can boot the online version of PXE-Knife using following command. 
 +<​code>​  
 +qemu -fda gpxe.dsk -net nic -net user -bootp http://​alien.doesntexist.org/​pxeknife/​pxelinux.0
 </​code>​ </​code>​
  
Line 30: Line 17:
 <​code>​ <​code>​
 #!gpxe #!gpxe
-echo "​Hi ​there"+echo "Hi, We will be using PXEKnife from URL http://​www.alien.doesntexist.org/​pxeknife/​"
 dhcp net0 dhcp net0
-set 209:​string ​pxelinux.cfg/​default +set 209:​string ​/pxeknife.cfg/​default 
-set 210:string http://10.0.0.2/​pxeknife/​ +set 210:string http://www.alien.doesntexist.org/pxeknife/ 
-chain http://10.0.0.2/​pxeknife/​pxelinux.0 +echo "Here we go" 
-boot+chain http://www.alien.doesntexist.org/​pxeknife/​pxelinux.0
 </​code>​ </​code>​
 and I compile with following command ​ and I compile with following command ​
Line 46: Line 33:
 qemu -fda gpxe.dsk qemu -fda gpxe.dsk
 </​code>​ </​code>​
-I do get my echo messages printed, but still I am getting same error. 
-<​code>​ 
-TFTP prefix: http://​10.0.2.2/​ 
-Trying to load: pxelinux.cfg/​default 
-Unable to locate configuration file 
  
-Boot failed: press a key to retry, or wait for reset... +===== Ready to use PXE-Knife over HTTP ===== 
-</​code>​+If you want to try out PXE-Knife without installing then visit page  [[pxeknifeOverHttp]] 
 + 
 + 
 +==== Problems ==== 
 +In case you encounter any problems with this then you can refer the page [[QemuPxeKnifeHTTPProbs]]
  

QR Code
QR Code wiki:qemupxeknifehttp (generated for current page)