Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Last revision Both sides next revision
wiki:qemupxeknifehttp [2009/05/23 10:35]
less1
wiki:qemupxeknifehttp [2009/05/23 12:12]
less1
Line 1: Line 1:
-====== Get PXE Knife working with QEMU over HTTP ======+====== Get PxeLinux and PXE-Knife working with QEMU over HTTP ======
  
-I am taking similar approach as I took for TFTP for which QEMU + PXE Knife combination is working if I use qemu TFTP stack. +Note : use latest version of Pxelinux to work over HTTP, for me version 3.80 worked.
-Here are the things that are working ​for me. +
-<​code>​ +
-qemu -net nic -net user -fda ./gpxe.dsk -bootp /pxelinux.0 -tftp /​home/​myname/​for_pxe_knife/​ +
-</​code>​ +
-which boots pxe-knife over tftp and  +
-<​code>​ +
-qemu -fda gpxe.dsk -net nic -net user -bootp http://​10.0.0.2/​gpxe/​gtest.gpxe +
-</​code>​ +
-boots gtest.gpxe which is copy of [[http://​etherboot.org/​gtest/​gtest.gpxe]].\\+
  
-But when I try and use HTTP with qemu over pxe_knife which is based on __pxelinux__,​ +Following ​is the way to run Pxe-knife (or any pxelinux ​based system) over http.
-it does not work.+
 <​code> ​ <​code> ​
 qemu -fda gpxe.dsk -net nic -net user -bootp http://​10.0.0.2/​pxeknife/​pxelinux.0 qemu -fda gpxe.dsk -net nic -net user -bootp http://​10.0.0.2/​pxeknife/​pxelinux.0
-</​code>​ 
-It loads pxelinux.0 successfully,​ but fails in loading //​pxeknife/​default//​ file with error  
-<​code>​ 
-TFTP prefix: http://​10.0.2.2/​ 
-Trying to load: pxelinux.cfg/​default 
-Unable to locate configuration file 
- 
-Boot failed: press a key to retry, or wait for reset... 
 </​code>​ </​code>​
  
Line 30: Line 12:
 <​code>​ <​code>​
 #!gpxe #!gpxe
-echo "​Hi ​there"+echo "Hi, We will be using PXEKnife from URL http://​www.alien.doesntexist.org/​pxeknife/​"
 dhcp net0 dhcp net0
-set 209:​string ​pxelinux.cfg/​default +set 209:​string ​/pxeknife.cfg/​default 
-set 210:string http://10.0.0.2/​pxeknife/​ +set 210:string http://www.alien.doesntexist.org/pxeknife/ 
-chain http://10.0.0.2/​pxeknife/​pxelinux.0 +echo "Here we go" 
-boot+chain http://www.alien.doesntexist.org/​pxeknife/​pxelinux.0
 </​code>​ </​code>​
 and I compile with following command ​ and I compile with following command ​
Line 46: Line 28:
 qemu -fda gpxe.dsk qemu -fda gpxe.dsk
 </​code>​ </​code>​
-I do get my echo messages printed, but still I am getting same error.+ 
 +===== Ready to use PXE-Knife over HTTP ===== 
 +If you want to try out PXE-Knife without installing then visit page  [[pxeknifeOverHttp]] 
 + 
 + 
 +==== Problems ==== 
 +In case you encounter any problems with this then you can refer the page [[QemuPxeKnifeHTTPProbs]]
  

QR Code
QR Code wiki:qemupxeknifehttp (generated for current page)