Differences

This shows you the differences between two versions of the page.

--- soc:2009:lynusvaz:notes:scripting_doc:features_added [2009/08/05 09:37]
lynusvaz
+++ soc:2009:lynusvaz:notes:scripting_doc:features_added [2009/08/16 00:19] (current)
lynusvaz
@@ Line 1: / Line 1: @@
-The features mentioned here are NOT YET part of mainline gPXE, and are still under development. The modified code can be found in my git repository, in the [[http://git.etherboot.org/?p=people/lynusvaz/gpxe.git;a=shortlog;h=refs/heads/offset|offset]] branch.
+=====Scripting Features=====
+The features mentioned here are NOT YET part of mainline gPXE, and are still under development. The modified code can be found in my git repository, in the [[http://git.etherboot.org/?p=people/lynusvaz/gpxe.git;a=shortlog;h=refs/heads/expt|expt]] branch.
-Scripting features:
   - Identifiers
   - Arithmetic evaluator
   - Quoting
-  - Return code
   - Branches
+  - Return code
   - Loops
-. See the Identifiers section at: [[http://etherboot.org/wiki/commandline]], for the basic syntax of an identifier. The new code allows identifiers to be 'nested', like:
+====Identifiers====
+See the Identifiers section at: [[http://etherboot.org/wiki/commandline]], for the basic syntax of an identifier. The new code allows identifiers to be 'nested', like:
   set i 0
   echo ${net${i}/ip}
-will print the IP address of the net0 interface.
+will print the IP address of the net0 interface. Arithmetic operations (see 2) can also be performed within the ${}:
+E.g.:
+  set i 0
+  echo ${net$(${i}+1)/ip}
+will print the IP address of the net1 interface (if it exists).
-. Arithmetic expressions can be evaluated by placing them within $().
+====Arithmetic Evaluation====
-The usual C operators (except assignment) are supported with their usual precendence. Also, string comparison is permitted.
+Arithmetic expressions can be evaluated by placing them within $().
-Identifiers are expanded by placing them within ${}.
+The following operators are supported (in order of decreasing precedence):
+  - !, ~          (logical NOT and bitwise negation)
+  - *, /, %       (multiplication, division, and modulo)
+  - +, -          (addition, subtraction)
+  - <<, >>        (left- and right-shift)
+  - <, <=, >, >=  (inequality)
+  - !=, ==        (equal, not equal)
+  - &             (bitwise AND)
+  - |             (bitwise OR)
+  - ^             (bitwise EX-OR)
+  - &&            (logical AND)
+  - ||            (logical OR)
+The == and != operators also act on strings. Identifiers are expanded by placing them within ${}.
 E.g.:
   echo $(1 + 2)
@@ Line 23: / Line 39: @@
   echo $(${a} * 3 + 5)
   echo $( ${net0/ip} != "" )
+Output:
-. Quoting:
+====Quoting====
 The \ is used as an escape character. The following sequences are recognised:
-\<space> Treats the space as part of the command-line argument
+  * \<space> Treats the space as part of the command-line argument
-\<tab> Ditto
+  * \<tab> Ditto
-\<newline> Concatenates the next line to the current line. Both the \ and the newline character are removed
+  * \<newline> Concatenates the next line to the current line. Both the \ and the newline character are removed
-\\ A literal \
+  * \<any other character> Removes the special meaning of the character (if any)
-\<any other character> Removes the special meaning of the character (if any)
+Within single-quotes, all characters lose their special meaning. Within double-quotes, the \ and $ retain their special meaning. Single- and double-quotes allow you to use a newline character in a command-line argument.
-Within single-quotes, all characters lose their special meaning. Within double-quotes, the \ and $ retain their special meaning.
 E.g.:
-  set message 'Hello World'
+  set message "Hello World"
   echo '${message} = '${message}
   set message Hello\ \ World
+  echo ${message}
   set message Hello\ World\ \#1	#'Hello World #1' is treated as a single argument
-  echo 'Hello
+  echo ${message}
-  World'
+  echo 'Hello
+  World'  # Will introduce a newline between Hello and World
   echo Hello \
   World
   echo It\'s good to see you!
+Output:
+  ${message} = Hello World
+  Hello  World
+  Hello World #1
+  Hello
+  World
+  Hello World
+  It's good to see you!
-. The return code of the previous statement can be checked using the ${rc} variable.
+====Branches====
-A value of 0 means that the command completed successfully, while any other value means the command was not successful.
-. Branches:
 The keywords if, else and fi are used to branch command execution:
   if <condition>
@@ Line 65: / Line 90: @@
       <backup statements>	#Call this statement sequence B
   done
-The statements in sequence A are executed one by one. If any of them fails, execution branches immediately to sequence B.
+The statements in sequence A are executed one by one. If any of them fails, execution branches immediately to sequence B. If all the statements in sequence A are executed successfully, execution skips sequence B, and continue after the done statement.
 E.g.:
-  if $( ${filename} == "")
+  if $( ${filename} != "" && ${server} != "")
-  	echo "No filename"
-  else
   	chain tftp://${server}//${filename}
+  else
+  	echo "No filename"
   fi
+will first check that neither filename and server are not empty, before attempting to boot. If either is empty, display an error message.
   try
@@ Line 81: / Line 107: @@
   	echo "Oops: ${rc}"
   done
+will attempt to boot using the given kernel and initrd. If any of the three commands fail, it displays a message.
-. While and for loops have been added:
+====Return Code====
+The return code of the previous statement can be checked using the ${rc} variable.
+A value of 0 means that the command completed successfully, while any other value means the command was not successful.
+E.g.:
+  dhcp net0
+  if $( ${rc} != 0 )
+      echo "DHCP failed"
+  else
+      chain http://etherboot.org/gtest/gtest.gpxe # (Tom's Root Boot disk)
+  fi
+====Loops====
+You can use while and for loops as:
   while <condition>
   do
@@ Line 105: / Line 145: @@
   	set i $( ${i} + 1 )
   done
+will attempt to get a dhcp connection on each valid interface, and if it is successful, boot using a given file.
-  for i in 0 1 2 3 $(3 + 1) 5
+  for i in 0 1 2 3 5 $(6*3)
   do
-  	dhcp net${i}
+        echo 'i =' ${i}
-  	if $(${rc} == 0)
-  		chain tftp://${server}//${filename}
-  	fi
   done
+displays:
+  i = 0
+  i = 1
+  i = 2
+  i = 3
+  i = 5
+  i = 18
+A break statement will exit a loop, and a continue statement will start the next iteration of the loop.
+  for i in 1 2 3 4 5 6
+  do
+        if $(${i} == 3)
+              continue
+        fi
+        echo 'i =' ${i}
+        if $(${i} == 4)
+              break      #This will exit the for loop, not just the if branch
+        fi
+  done
+displays:
+  i = 1
+  i = 2
+  i = 4

Trace:

Differences

Navigation

Search

Toolbox

QR Code