Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
romburning:tg3 [2008/03/06 07:25] mcb30 |
romburning:tg3 [2008/03/06 07:28] mcb30 |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== Burning gPXE into Broadcom BCM57xx-based cards ====== | ||
- | |||
- | <referback>This page is part of the [[:romburning|ROM-burning]] tutorial.</referback> | ||
- | |||
- | The Broadcom Diagnostic Utility set allows you to update the expansion ROM images in Broadcom BCM57xx gigabit network cards (and rebranded Broadcom cards such as the HP NC7771). | ||
- | |||
- | ===== Preparing the ROM image ===== | ||
- | |||
- | Copy the gPXE ROM image (e.g. //bin/0e1100ca.rom//) to a FAT-formatted floppy disk or USB drive. | ||
- | |||
- | ===== Preparing the tools ===== | ||
- | |||
- | Download the Broadcom Diagnostics Utility from [[http://www.broadcom.com/docs/driver_download/570x/B57udiag-10.53.iso]]. Burn this image to CD using your favourite CD burning method. | ||
- | |||
- | ===== Burning the gPXE ROM ===== | ||
- | |||
- | Boot from the CD and select the following sequence of options: | ||
- | |||
- | * "Continue to boot FreeDOS from CD-ROM" | ||
- | * "Install to harddisk using FreeDOS setup" (which won't actually install anything to your hard disk) | ||
- | * The language of your choice | ||
- | * "Run FreeDOS from CD-ROM (return to command prompt)" | ||
- | |||
- | You should now see an //X:\>// prompt. Type | ||
- | |||
- | cd \b57udiag | ||
- | b57udiag -ver | ||
- | |||
- | You should see something like | ||
- | |||
- | X:\>cd \b57udiag | ||
- | X:\B57UDIAG>b57udiag -ver | ||
- | **************************************************** | ||
- | Copyright(c) 2000-2007 Broadcom Corporation | ||
- | Broadcom NetXtreme User Diagnostics 10.53 (07/27/07) | ||
- | **************************************************** | ||
- | C Brd:Rv Bus PCI Spd Base Irq EEP MAC Fmw Configuration | ||
- | - ------- ------- --- --- ---- -- ---- ------------ ---------- ------------- | ||
- | 0 5703:B0 05:04:0 32 33 FC50 11 128k 00110AE99C0B 5703-v.235 WMp,auto | ||
- | 1 AC1K:B5 05:00:0 32 33 FF7F 9 4k 00095B1C29D9 2.5 auto | ||
- | |||
- | This shows the list of Broadcom cards in the machine. Select the card that you wish to burn gPXE into, and identify its card number (from the left-hand "C" column in the listing). | ||
- | |||
- | To burn gPXE into the card, type | ||
- | |||
- | b57diag -c 0 -pxe c:\0e1100ca.rom | ||
- | |||
- | where "-c 0" specifies the card number of the card that you wish to burn gPXE into, and "c:\0e1100ca.rom" is the path to the gPXE ROM image on your FAT-formatted floppy disk or USB drive. You should see something like: | ||
- | |||
- | X:\B57UDIAG>b57udiag -c 0 -pxe c:\0e1100ca.rom | ||
- | **************************************************** | ||
- | Copyright(c) 2000-2007 Broadcom Corporation | ||
- | Broadcom NetXtreme User Diagnostics 10.53 (07/27/07) | ||
- | **************************************************** | ||
- | C Brd:Rv Bus PCI Spd Base Irq EEP MAC Fmw Configuration | ||
- | - ------- ------- --- --- ---- -- ---- ------------ ---------- ------------- | ||
- | 0 5703:B0 05:04:0 32 33 FC50 11 128k 00110AE99C0B 5703-v.235 WMp,auto | ||
- | | ||
- | 0 5703:B0 05:04:0 32 33 FC50 11 128k 00110AE99C0B 5703-v.235 WMp,auto | ||
- | Updating PXE-UNDI16 code (length = 59908 bytes ) ... | ||
- | Programing 59908 bytes to NVRAM offset 00001A60 | ||
- | Updating Directory... | ||
- | code len = 0000ea04 | ||
- | sram_start_address = 00010000 | ||
- | code_start_address = 00001a60 | ||
- | Reading current NVRAM ... OK | ||
- | Programing : 512 | ||
- | Totally 1 card(s) has been programmed. | ||
- | |||
- | Reboot the machine and enter the BIOS setup. You should see gPXE show up as an option in your BIOS's boot selection menu. | ||
- | |||
- | Congratulations on successfully burning gPXE into your network card! | ||