Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
wiki:qemupxeknife [2009/05/22 19:35] less1 |
wiki:qemupxeknife [2009/05/23 09:43] (current) less1 |
||
|---|---|---|---|
| Line 47: | Line 47: | ||
| Here is the code which is working for | Here is the code which is working for | ||
| <code> | <code> | ||
| - | qemu -net nic -net user -boot n -hda ./testing.img -bootp /pxelinux.0 -tftp /home/myname/for_pxe_knife/ | + | $ qemu -net nic -net user -boot n -hda ./testing.img -bootp /pxelinux.0 -tftp /home/myname/for_pxe_knife/ |
| + | $ qemu -net nic -net user -fda ./gpxe.dsk -bootp /pxelinux.0 -tftp /home/myname/for_pxe_knife/ | ||
| </code> | </code> | ||
| for following version of qemu version qemu version 0.10.0 | for following version of qemu version qemu version 0.10.0 | ||
| Line 53: | Line 54: | ||
| $ qemu | $ qemu | ||
| QEMU PC emulator version 0.10.0, Copyright (c) 2003-2008 Fabrice Bellard | QEMU PC emulator version 0.10.0, Copyright (c) 2003-2008 Fabrice Bellard | ||
| + | </code> | ||
| + | |||
| + | ==== Problems ==== | ||
| + | |||
| + | As per me following command should have worked, but It did not worked | ||
| + | |||
| + | <code> | ||
| + | $ qemu -bootp tftp://10.0.2.2//pxelinux.0 -tftp /home/myname/for_pxe_knife/ -fda gpxe.dsk | ||
| + | </code> | ||
| + | at same time command | ||
| + | <code> | ||
| + | $ qemu -bootp /pxelinux.0 -tftp /home/myname/for_pxe_knife/ -fda gpxe.dsk | ||
| + | </code> | ||
| + | works. | ||
| + | |||
| + | Problem faced is,\\ | ||
| + | it successfully downloads the //pxelinux.0// and executes it, | ||
| + | but it fails when it is downloading pxelinux.cfg/default\\ | ||
| + | It gives an error saying | ||
| + | <code> | ||
| + | TFTP prefix: tftp://10.0.2.2// | ||
| + | Trying to load: pxelinux.cfg/default | ||
| + | Unable to locate configuration file | ||
| + | |||
| + | Boot failed: press a key to retry, or wait for reset... | ||
| </code> | </code> | ||
| Line 66: | Line 92: | ||
| QEMU PC emulator version 0.9.1, Copyright (c) 2003-2008 Fabrice Bellard | QEMU PC emulator version 0.9.1, Copyright (c) 2003-2008 Fabrice Bellard | ||
| </code> | </code> | ||
| + | |||
| + | But if you provide gpxe.dsk instead of ./testing.img it uses gpxe.dsk stack and boots properly. | ||
| + | <code> | ||
| + | $ qemu -net nic -net user -fda ./gpxe.dsk -bootp /pxelinux.0 -tftp /home/minix-pravin/Etherboot/v2/pxeknife/pxeknife/ | ||
| + | </code> | ||
| + | |||
| + | ==== Useful links ==== | ||
| + | - [[http://syslinux.zytor.com/wiki/index.php/PXELINUX]] About pxelinux | ||
| + | - [[http://syslinux.zytor.com/wiki/index.php/Development/Testing]] for using qemu with pxelinux. | ||
