✎ syslinux - Etherboot/gPXE Wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.

====== Booting gPXE from a memory stick partition with SYSLINUX ======
Much like the howto [[:usbwithstorage]], this will guide you through installing gPXE on your flash drive (or any other FAT/ext234/btrfs partition for that matter) without losing ability to store files on it. In fact, using EXTLINUX or SYSLINUX, it's possible to use this method to make almost any medium gPXE-bootable.

==== Getting SYSLINUX ====
I'll leave this part mostly down to you. It's probably available in your distribution's package manager, but if not, you can get it from http://syslinux.zytor.com


==== Making the partition bootable ====
The partition will first need to be labelled as "boot" using fdisk.

Start fdisk. As root:
<code>fdisk /dev/sdb</code>
Replace /dev/sdb with your disk.

Type "p" to show your partition table. Eg, heres mine:
<code>   Device Boot      Start         End      Blocks   Id  System
/dev/sdb1               1        1012     1035245   83  Linux
</code>
Identify which partition it is which you want to make bootable. If, like me, you only have one, this task is trivial.

Type "a" to toggle the bootable flag, and it will ask you which partition number. This done, you can type "w" to write the changes and exit.

==== Building and copying the gPXE image ====
Simply enter the source directory (gpxe-*/src) and:
<code>make bin/gpxe.lkrn</code>
This creates a gPXE image which acts a bit like a linux kernel, meaning SYSLINUX will recognise it as its own.

Copy this to your mounted flash drive:
<code>cp bin/gpxe.lkrn /media/disk/</code>
Replace /media/disk/ with the appropriate path.

==== Installing SYSLINUX ====
//Follow these steps if you are using a FAT16 or FAT32 partition//

Now SYSLINUX will need a config file. Here's how you can make a really simple one. No menus or anything:
<code>cat > /media/disk/syslinux.cfg << EOF
default gpxe
label gpxe
kernel /gpxe.lkrn
EOF
</code>

If you want anything more complex, see the SYSLINUX documentation.

Now that the config's done, you can unmount (but don't eject!) the disk. If in doubt, just use the umount command.
To install SYSLINUX on the partition, as root:
<code>syslinux -s /dev/sdb1</code>
Replacing /dev/sdb1 with your partition.

Continue with the "Installing an MBR" section below.

==== Installing EXTLINUX ====
//Follow these steps if you're using an ext2/3/4 or btrfs partition. ext4 and btrfs are only supported in EXTLINUX 4.0.0 and later//

EXTLINUX requires a different filename for its config file compared to SYSLINUX. Generate a simple one like this:
<code>cat > /media/disk/extlinux.conf << EOF
default gpxe
label gpxe
kernel /gpxe.lkrn
EOF
</code>

To install EXTLINUX, you don't even need to unmount the medium. As root, simply:
<code>extlinux -i /media/disk/</code>

Continue with the "Installing an MBR" section below.

==== Installing an MBR ====

You should have a SYSLINUX mbr.bin file somewhere on your system. For me, it was /usr/share/syslinux/mbr.bin
As root, write this to your flash drive:
<code>dd if=/usr/share/syslinux/mbr.bin of=/dev/sdb</code>

And you're done! Now you should be able to boot gPXE from the memory stick.

Trace: • pxekniferomomatichttp • debian_etch_iscsi • week11 • oremanj • sed_-_build_instructions • nikhilcrao • stefanha • aoeboot • welcome • week5 • intel • week12 • asdlkf