✎ sanboot:win2k8_iscsi_install - Etherboot/gPXE Wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Installing Windows Server 2008 to an iSCSI target =====

To install Windows Server 2008 to an iSCSI target, you must first configure your system to attempt to boot via iSCSI, and fall back to booting from DVD-ROM if the iSCSI boot fails.  The exact procedure for doing this will vary depending on your computer's BIOS.

===== Configuring the BIOS boot order =====

Enter your BIOS setup screen.  (Typically, this will require you to press a key such as DEL or one of the function keys F1-F12 immediately after rebooting the system.)

Configure your BIOS to attempt booting in the following order:

  - Boot using gPXE.
  - Boot from DVD-ROM.

===== Configuring gPXE for iSCSI boot =====

Place the following lines in ///etc/dhcpd.conf//:

  option space gpxe;
  option gpxe-encap-opts code 175 = encapsulate gpxe;
  option gpxe.keep-san code 8 = unsigned integer 8;
  
  filename "";
  option root-path "iscsi:my.target.dns.name::::iqn.2007-08.name.dns.target.my:iscsiboot";
  option gpxe.keep-san 1;

where //my.target.dns.name// is the DNS name (or IP address) of your iSCSI target, and //iqn.2007-08.name.dns.target.my:iscsiboot// is the iSCSI target IQN that you wish to boot from.

You will probably need to restart your DHCP server for the changes to take effect:

    root@chipmunk# /etc/init.d/dhcpd restart

===== Starting the installation =====

Place the Windows Server 2008 DVD-ROM in the drive, and switch on the computer.  You should see it attempt to boot via iSCSI, fail, and then boot from the DVD-ROM.  Once you reach the point of selecting an installation disk drive, you should see your iSCSI disk appear in the list:

**Note:** If you get the message "//This computer's hardware may not support booting to this disk. Ensure that the disk's controller is enabled in the computer's BIOS menu.//" or "//Windows is unable to find a system volume that meets its criteria for installation.//", do the following: Create a new partition on the disk and format it. Then exit the setup and try again after a reboot. More information can be found in [[http://support.microsoft.com/kb/KB933925|this article.]]

{{ :screenshots:win2k8_iscsi_install.png?800x600 |Windows Server 2008 installation disk selection}}

===== Completing the installation =====

Continue the installation as normal.  Your computer will reboot a few times during installation; you can safely leave it unattended during this time.

Congratulations on successfully installing Windows Server 2008 to an iSCSI target!

{{ :screenshots:win2k8_iscsi_boot.png?800x600 |Windows Server 2008 booted from an iSCSI target}}


==== What to do if the installation can't find the iSCSI disk. ====

  - Ensure the iSCSI target is working by connecting it with existing os. To make your life easy, You can unset the password for the iSCSI target for testing.
  - Reboot the into gPXE, then press <code>Ctrl-B</code> to get the command line.
  - In the command line, type <code>dhcp net0</code> You'll see response which is like: <code>DHCP (net0 xx:xx:xx:xx:xx:xx)... ok</code>
  - In the command line, type <code>set keep-san 1</code>
  - And in command line, type <code>sanboot iscsi:my.target.dns.name::::iqn.2007-08.name.dns.target.my:iscsiboot</code> If you see something like "Preserving connection to SAN disk." in response, You are on the half way.
  - In the command line, type <code>exit</code>
  - Go on with the installation above.

**NOTE:** If you are installing vista, be sure to read the NOTE in [[sanboot:winvista|Vista install guide]] to save your time.

**NOTE:** Windows Setup creates an explicit route to your your iSCSI target using your default gateway. This means if your target is on the same LAN, your router must be prepared to route local LAN traffic (which normally it would not do as the initiator and target could communicate directly). Some strict firewall settings will prevent this kind of routing which will cause Windows Setup to be unable to see the iSCSI drive. For example, using Shorewall you need to enable the "routeback" setting on the LAN interface. You can examine the route settings by pressing SHIFT+F10 when the drive selection window is displayed, then typing "route print" at the DOS command prompt.

===== What to do if the installation says: "Ensure that the disk's controller is enabled in the computer's BIOS menu" =====

If you can't continue with windows installation on iSCSI Target with an error message
  Windows cannot be installed to this disk. This computer's hardware may not support booting to this disk. Ensure that the disk's controller is enabled in the computer's BIOS menu
Solution for this error is quite simple, just add a drive for installation time, if the drive is a Serial-ATA connected then set it to //Compatibile Mode// not //AHCI//. If you start windows installer once again you will see an error message only at the physical drive, select iSCSI target and just click next.
Trace: • aoebootprepdebianetch • debian_etch_iscsi • winpe • srp_install • iscsi_create_target • iscsi_via_linux • commerciallinks
Navigation

Search

Toolbox

QR Code
